DIY Tent Supplies:
- 10 – 1/2″ PVC plumbing pipes {they come in a 10′ length}
- 2 – 10 piece bags of 1/2″ 90 degree ELBOW
- 2 – 10 piece bags of 1/2″ TEE
- Ratcheting PVC Cutter
- 5 – Sheets
How to Make A Tent:
- My friend had her local home improvement store cut the tent pipes, but my Home Depot was not that accommodating, so I purchased a Ratcheting PVC Cutter to do it myself at home. They are very easy to use and it did give me the freedom to cut the pieces the exact size I wanted once I figured out what we were going to make. I cut 8 of the pipes into 2 – 4′ pieces and one 2′ section.
- After some serious math calculations which included my 5th grader, husband and the Pythagorean theorem, I cut 2 of the longer PVC pipes into sections that were 2′ 9 7/8″ so that a 90 degree elbow could be used at the roof peaks. I labeled these pieces with a Sharpie “R” for “roof” so they could be easily identified when needed.
- Several of the smaller 2′ pieces I cut into 2″ inch pieces to be used as connectors.
- To make the structure shown here you would need: 12 – 4′ segments, 4 – “R” segments, 10 – 90 degree ELBOW pieces, 12 – TEE pieces and 12 – 2″ connectors {small cut piece of regular pipe}.
- Add sheets and move in {I learned that blankets were more likely to cause a weight shift, but could be used if a more stable structure was built}.
We made several variations of this structure substituting 2′ segments for several of the WALL portions to help add stability. If you are doing this with small children, it might be best to start with smaller pipe sections and use chairs or a tree for support since it is likely to shift and fall over with JUST this configuration.
Because the PVC pipe joints are not as functional as Tinker Toy connectors, there is a little problem-solving when it comes to how to put things together. You can see my lower and upper corners pictured here. The TEE segments are complimented by adding a 2″ connector piece that joins the ELBOW below. On the upper corner, two TEEs are used – one for the supporting vertical post and one at an angle for the roof.
This is great! I love the part about the PVC making decent musical instruments and awesome weapons. My boys are going to love this. Can’t wait to show my husband and get started! Thanks!
That looks like so much fun! And such a great activity for kids!
omg this is fabulous! my kids are nearly grown but i still want one!
BRAVO.
come visit anytime.
michele
How fun! My daughters would love this! I ™d love if you ™d come share this at my link party going on right now.
http://mylilpinkpocket.blogspot.com/2011/08/show-share-3.html
Marie
mylilpinkpocket.blogspot.com
great post! i love tents. brings me back to my childhood! 🙂
Totally love this. Sharing a link to this post with my Facebook readers.
Thx so much for this article. I want to make similar structure for a sukkoh for the upcoming Jewish holidays. Do you think I could use the same principles to make a rectangular structure 10 ft length and 5 ft depth or is the PVC to flimsy for such a large structure?
I created a similar system 6 years ago. It’s a giant set of “lincoln logs”. I have 2 foot pieces, 1 foot pieces, 45 degree joints, 90 degree joints, T joints, and just the plain joint. Then after my husband started building with our daughter and I, we went and got a special three way corner joint. It cost a little bit more than the other joints but it is so handy when you want to build a square. I then went to the second hand store and got scrap fabrics and a bag of clothes pins. We make tunnels and forts whenever we are inspired to and it all fits nicely in a giant Rubbermaid container.
That is so cool! My kids would love it!
Jen 🙂
We did the same thing a year ago while staying with my parents. Our two big girls didn’t have much of a play area, so we made a tent out of PVC pipe. Covered it with spare fabric and table cloths sewn together. Put a rug and a couple of chairs in there. They loved it!